Ctek Automation Control Application APN007 Bedienungsanleitung Seite 1

Application NoteCtek Automation Control ApplicationAPN007Release 4.02.02Ctek – Things That Move Data.

Application Note – Automation Control ApplicationAPN007 25 July, 20145Figure 4 - Unit ConfigurationLocation Name:A descriptive name assigned to this

Application Note – Automation Control ApplicationAPN007 25 July, 20146SMS Remote Control:Enable or disable SMS read/write control/monitoring of auto

Application Note – Automation Control ApplicationAPN007 25 July, 20147Authentication and SSL Encryption:Settings specific to each email SMTP server.

Application Note – Automation Control ApplicationAPN007 25 July, 20148ABOUT I/O MODULE ADDRESSINGI/O module part numbers B1204S (4-port relay), B121

Application Note – Automation Control ApplicationAPN007 25 July, 20149Figure 7 - Module Delete ScreenReplace:The replace function has three purposes

Application Note – Automation Control ApplicationAPN007 25 July, 201410Note:The default commend described above uses a broadcast that will set the a

Application Note – Automation Control ApplicationAPN007 25 July, 201411Configure OutputsA representative portion of the Configure Outputs navigation

Application Note – Automation Control ApplicationAPN007 25 July, 201412Output Configuration ScreensFigures 8 – 11 below show the configuration scree

Application Note – Automation Control ApplicationAPN007 25 July, 201413Figure 14 - Output Virtual/Numeric

Application Note – Automation Control ApplicationAPN007 25 July, 201414Pin NamePin TypeDescriptionOutput NameAllAssigns a name to the output pin tha

25 July 2014iContentsTABLE OF FIGURES...

Application Note – Automation Control ApplicationAPN007 25 July, 201415Configure InputsThis is a selection screen. Use the Type pull-down and Edit b

Application Note – Automation Control ApplicationAPN007 25 July, 201416Figure 17- Input Physical/DigitalFigure 18 - Input Physical/Analog

Application Note – Automation Control ApplicationAPN007 25 July, 201417Figure 19 - Input Physical/PulseFigure 20 - Input Virtual/Digital

Application Note – Automation Control ApplicationAPN007 25 July, 201418Figure 21 - Input Virtual/Numeric

Application Note – Automation Control ApplicationAPN007 25 July, 201419Input Pin NamePin TypeDescriptionKey: PD = Physical Digital, PA = Physical An

Application Note – Automation Control ApplicationAPN007 25 July, 201420AlarmPA, PP, VNOn/Off for SMS and email Alarms associated with a specific thr

Application Note – Automation Control ApplicationAPN007 25 July, 201421somewhat smaller than the theoretical due to sensor characteristics and minor

Application Note – Automation Control ApplicationAPN007 25 July, 201422Digital Input Pins – Source of InputsFigure 23 - Input Sources (Digital)Digit

Application Note – Automation Control ApplicationAPN007 25 July, 201423Numeric Input Pins – Source of InputsFigure 25 - Input Sources NumericAnalog

Application Note – Automation Control ApplicationAPN007 25 July, 201424Input Definitions – Virtual Numeric InputsInput PinsAny Physical or Virtual I

25 July 2014iiMore About Digital Inputs and Outputs ...

Application Note – Automation Control ApplicationAPN007 25 July, 201425Min/Max Range and Sensor Calibration:Range refers to the range or precision o

Application Note – Automation Control ApplicationAPN007 25 July, 201426Analog Input ProcessingFigure 27 - Analog Input ProcessingThresholdsThere are

Application Note – Automation Control ApplicationAPN007 25 July, 201427boundaries of an operating range that would otherwise be in conflict with lev

Application Note – Automation Control ApplicationAPN007 25 July, 201428Pulse Input - LatchingThe setting Greater Than Latch Function is a special ca

Application Note – Automation Control ApplicationAPN007 25 July, 201429Configure FormulasCtek's Automation Control application provides support

Application Note – Automation Control ApplicationAPN007 25 July, 201430Figure 30 - Edit Input FormulaOperandsCurrent Input Pin:Selects the input val

Application Note – Automation Control ApplicationAPN007 25 July, 201431Max – Min Units:The value (Maximum Units - Minimum Units) becomes the next op

Application Note – Automation Control ApplicationAPN007 25 July, 201432Figure 31 - Standard Conversion FormulaThe standard conversion formula shown

Application Note – Automation Control ApplicationAPN007 25 July, 201433ProgramsPrograms are named groups of functions that can be applied to a speci

Application Note – Automation Control ApplicationAPN007 25 July, 201434Figure 33 – Program Edit ScreenProgram Edit FieldsProgram NameThe user define

25 July 2014iiiDigital I/O – Set ...

Application Note – Automation Control ApplicationAPN007 25 July, 201435Log and LoggingSet Up and ManagementThe Automation Control application mainta

Application Note – Automation Control ApplicationAPN007 25 July, 201436The Control PanelThe Control Panel for the Automation Control provides a cons

Application Note – Automation Control ApplicationAPN007 25 July, 201437Figure 35 - Sample Control Panel Display

Application Note – Automation Control ApplicationAPN007 25 July, 201438Appendix A – Function LibraryFunctions are predefined building blocks used to

Application Note – Automation Control ApplicationAPN007 25 July, 201439Parameters = o 6 u 1Numeric I/O – SetNumeric I/O – Set P1 P2 P3 P4P1 and P2 d

Application Note – Automation Control ApplicationAPN007 25 July, 201440Note on Remote CommandsRemote operations are those decisions and resulting ac

Application Note – Automation Control ApplicationAPN007 25 July, 201441Timer/Counter – Start [Note – Changed In Release 4.02.02]Timer/Counter – Star

Application Note – Automation Control ApplicationAPN007 25 July, 201442Timer/Clock – Start P1 P2 P3 P4 P5 P6 P7P1 = i for input or o for output (dig

Application Note – Automation Control ApplicationAPN007 25 July, 201443Timer/Alarm Override – Start [Note – Changed In Release 4.02.02]cP1 P2 P3 P4T

Application Note – Automation Control ApplicationAPN007 25 July, 201444d) All hour timers (defined by P5) must be housed in outputs. The value of P5

25 July 2014ivTable of FiguresFIGURE 1 – THEORY OF OPERATION ...

Application Note – Automation Control ApplicationAPN007 25 July, 201445Application Status – Set [Note – New In Release 4.02.02]Application Status –

Application Note – Automation Control ApplicationAPN007 25 July, 201446Action: Application Status – SetParameters: 5 0 6 ANOTE – Force status update

Application Note – Automation Control ApplicationAPN007 25 July, 20141Introduction:Ctek's Automation Manager is an optional firmware applicatio

Application Note – Automation Control ApplicationAPN007 25 July, 20142(digital), basic math functions (numeric), and can be assigned event threshold

Application Note – Automation Control ApplicationAPN007 25 July, 201434. Configure outputs on each installed module5. Create and assign formulas as

Application Note – Automation Control ApplicationAPN007 25 July, 20144User Interface and Configuration SpecificsSelecting the Automation Control Con